Difference between revisions of "Talon X-UAV Mobius Gimbal Project"
From ItsQv
| (3 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
| − | + | [[File:BTI.png|link=GIMBALS|Gimbals]]<br> | |
<i>April 2015</i><br> | <i>April 2015</i><br> | ||
<br> | <br> | ||
| Line 5: | Line 5: | ||
|- | |- | ||
| align="left" valign="bottom" width="50%" | __TOC__ | | align="left" valign="bottom" width="50%" | __TOC__ | ||
| − | | align="right" width="50%" | [[File:BGP16. | + | | align="right" width="50%" | [[File:BGP16.JPG|500px]] |
|- | |- | ||
| | | | ||
| Line 12: | Line 12: | ||
== Introduction == | == Introduction == | ||
| + | |||
| + | Expanding on several solid camera mounts, I added a 2 axis, roll and pitch, brushless assembly to the fron of the Talon. The idea was to get it to fit inside the clear dome and while I was able to do this, the dome itself did not prove to be that useful as it very quickly became scratched and always had a slight reflection problem. So I chopped the dome up just enough to clear the sight lines of the camera and it worked very well smoothing out the pitch and roll. | ||
| + | |||
| + | {| border="0" cellspacing="0" cellpadding="0" align="center" | ||
| + | |- | ||
| + | | align="center" | [[File:MOB GIM v003a.jpg | 800px]] | ||
| + | |- | ||
| + | | align="center" | Exploded view | ||
| + | |}<br><br> | ||
| + | |||
| + | {| border="0" cellspacing="0" cellpadding="0" align="center" | ||
| + | |- | ||
| + | | align="center" | [[File:TAL GIM 002.jpg | 600px]] | ||
| + | |- | ||
| + | | align="center" | Front corner view of assembly | ||
| + | |}<br><br> | ||
| + | |||
| + | {| border="0" cellspacing="0" cellpadding="0" align="center" | ||
| + | |- | ||
| + | | align="center" | [[File:TAL GIM 003.jpg | 600px]] | ||
| + | |- | ||
| + | | align="center" | Rear corner view of assembly | ||
| + | |}<br><br> | ||
| + | |||
| + | === Parts List === | ||
| + | |||
| + | Motors, Controller & Hardware<br> | ||
| + | :1ea HK2804 gimbal motor | ||
| + | :1ea iPower 2212 Brushless Gimbal motor | ||
| + | :Storm32 v1.1 or newer brushless gimbal controller | ||
| + | :Various M3x8 socket head cap screws with flat washers | ||
| + | :6 M3x6 flat head screws | ||
| + | :Align PJ Gel Pad | ||
| + | :Small wire ties<br><br> | ||
| + | |||
| + | 3D Prints | ||
| + | :Camera Base Plate - Mob_Gim_Plate_v001 | ||
| + | :Camera Roll Plate - Mob_Gim_Roll_Plate_v001 | ||
| + | :Roll Arm Bracket - Mob_Roll_Brkt_v003c | ||
| + | :Roll Motor Bracket - Roll_Motor_Brkt_v002 | ||
| + | :Assembly Back Plate - MOB_MNT_BackPlate_v001 | ||
| + | :Assembly Front Plate - MOB_MNT_FrontPlate_v004 | ||
| + | |||
| + | Camera<br> | ||
| + | :Mobius with lens '2C' modified for vertical mount<br><br> | ||
| + | |||
| + | === Files === | ||
| + | |||
| + | Here are the print files if you would like to give this a try. The zip contains the printable pieces and image files, simply richt-click the link and select "Save Target" for the download. If you would like the native SolidWorks files, please drop me a line (below) and I will accomodate.<br><br> | ||
| + | |||
| + | [http://www.itsqv.com/share/Talon_Mobius_2_Axis_Gimbal.zip Talon Mobius 2 Axis Gimbal ZIP] | ||
| + | <br><br> | ||
| + | |||
| + | === Comments? Questions? === | ||
| + | |||
| + | :'''<u>[mailto:qmar80@hotmail.com?Subject=About%20the%20Talon%20X-UAV%20Gimbal&body=Question? email me!]</u>''' | ||
| + | |||
| + | == See Also == | ||
| + | |||
| + | TBA<br> | ||
| + | |||
| + | <br><br><br> | ||
| + | [[Category:Contents]] | ||
Latest revision as of 13:11, 18 March 2016
April 2015
| |
| Talon front mount 2 Axis gimbal |
Introduction
Expanding on several solid camera mounts, I added a 2 axis, roll and pitch, brushless assembly to the fron of the Talon. The idea was to get it to fit inside the clear dome and while I was able to do this, the dome itself did not prove to be that useful as it very quickly became scratched and always had a slight reflection problem. So I chopped the dome up just enough to clear the sight lines of the camera and it worked very well smoothing out the pitch and roll.
|
| Exploded view |
|
| Front corner view of assembly |
|
| Rear corner view of assembly |
Parts List
Motors, Controller & Hardware
- 1ea HK2804 gimbal motor
- 1ea iPower 2212 Brushless Gimbal motor
- Storm32 v1.1 or newer brushless gimbal controller
- Various M3x8 socket head cap screws with flat washers
- 6 M3x6 flat head screws
- Align PJ Gel Pad
- Small wire ties
3D Prints
- Camera Base Plate - Mob_Gim_Plate_v001
- Camera Roll Plate - Mob_Gim_Roll_Plate_v001
- Roll Arm Bracket - Mob_Roll_Brkt_v003c
- Roll Motor Bracket - Roll_Motor_Brkt_v002
- Assembly Back Plate - MOB_MNT_BackPlate_v001
- Assembly Front Plate - MOB_MNT_FrontPlate_v004
Camera
- Mobius with lens '2C' modified for vertical mount
Files
Here are the print files if you would like to give this a try. The zip contains the printable pieces and image files, simply richt-click the link and select "Save Target" for the download. If you would like the native SolidWorks files, please drop me a line (below) and I will accomodate.
Talon Mobius 2 Axis Gimbal ZIP
Comments? Questions?
See Also
TBA
