Difference between revisions of "Strix StratoSurfer Twin Conversion"

Latest revision as of 13:25, 12 April 2020

Mark Qvale - February, 2019

Contents 1 Introduction 2 General Specifications 3 Components/Flight Gear 3.1 Power Set-up 3.1.1 Motor Mounts 3.2 Motor Mount Body Install 3.3 Wing Mount 3.4 Flight Control 4 Re-Maiden! 4.1 Parting Shot 5 Project 3D Print Files 6 See Also 6.1 Some of the Vendors I used for this project 6.2 Comments? Questions?
	Super Stratosurfer!

Introduction

I have found that I have no love for the top mounted motor on these types of powered gliders. I do love the way the Strix StratoSurfer flys especially with the Matek F405-wing controller running Chibios/Arduplane -but- the top motor position and angle is a PITA in terms of trimming the plane, noise and launches wanting to nose-dive. So with that, and after one year and over 100 flights with this plane, I've decided to convert it to a twin tractor set-up.

Below are my build notes, print files and a flight review of this now re-configured plane.

General Specifications

Seller - ReadyMadeRC, USA
Aircraft - Strix Stratosurfer
Modification Date - 1 February, 2019

Components/Flight Gear

Below is the approximate layout of installed components:

Power Set-up

For power on this build I have started with iFlight T2207-1750kv motors and 35A Wraith32 BLHELI ESC's with active freewheeling. I've also added a pair of 1000mfd/35v Low ESR capacitors for noise and v-spike damping.

• Motor - iFlight T2207-1750kv
• ESC - 35A Wraith32 BLHELI ESC's
• Prop - APCe 6 x 4.5 Bull Nose
• Battery - Multistar 4S/5200, 10C or a 4S/7000 Li-Ion
  
  

Published specs for the iFlight motor

Prop chart for the iFlight motor

Motor Mounts

This design is very similar to some that I did for the Mini Talon. My goal was to make it light, slippery and strong. For my build I printed these in Hatchbox ABS filament at .2mm quality.

Fasteners used:

4x M3 x 8mm button head screws (Steel)

4x M3 x 8mm phillips head screws (Nylon)

Print orientation

Motor Mount Body Install

Mounting these is simple enough. Put the wing halves together on the wing spar, measure 200mm either side of the center and set some pins for location. 200mm doesn't interfere with flap servos should you choose this option and you can run up to about a 10" prop. Make sure the mount bodies are pushed all the way into the leading edge and use a straight edge to ensure the front faces are parallel. Glue and clamp them in place for 24hrs. I use E6000 glue as it works very well attaching PLA, PETG and ABS to EPO foam. Other glues that also work very well are UHU-POR, Beacons FoamTac and Gorilla Clear Contact cement. Do not use Gorilla expanding glue as it does not bond well to EPO and heat cycling can cause it to separate.

Front Piece

After printing use a clamp to maintain the integrity of the front piece and tap the four radial holes to M3. Once tapped, coat the threads with thin CA to add strength. You may have to file or sand the outside diameter of the four ears so the front piece will fit into the main mount body.

Clamped front piece

Motor Wire Routing

For wire routing I hot-wired a hole in the center of the motor mount, below the leading edge to a depth of ~50mm. This coincides with a hollow area that goes nearly to the wing root. You will have to go under a small leading edge spar and angle the hole upwards a bit. I then hot-wired a hole centered in the front/center notch deep enough to access the same hollow area. I ran a piece of silicone wire so that I could pull the ESC/motor wires through the wing to the front of the mount. Last I soldered on R30 - 2.0mm x 3 pin motor connectors and the ESC's.

Wire route

ESC Mounting

I decided to simply use hot glue to attach the ESC's to the bottom of the wing. I did have to cut small notches to accommodate the two capacitors but this was easy enough.

ESC craddle

Wing Mount

The rear wing mount is a copy of the lower portion of my extra tall Cobra motor mount and uses 2 - M3 x 30mm screws. The front wing mount comes from my Stratosurfer catalog low-profile canopies page and uses 2 - M3 x 40mm screws.

NOTE: If you are not using one of my low profile canopies, you will need to shave the stock foam canopy down to match the profile of the front wing mount.

Example of a shaved foam canopy

Flight Control

Since I am already using the Matek F405-wing flight controller with Chibios/Arduplane firmware there is absolutely no reason to change this, it is fantastic!

Links to this board -

• Matek F405-wing Flight Controller

GPS

For the GPS I am using the Beitian BN-220 mini ublox unit from Banggood.com. I have mounted it under the small rear hatch.

• Beitian BN-220 GPS Module

Re-Maiden!

Maiden - 01 February, 2019

Weather was perfect with temp at ~70F a very light breeze and clear skies. The first flight was uneventful in terms of drama and I flew her for about 20 minutes. In two subsequent flights I did an uneventful hand launch a session of auto-tune and lots of rolls, loops and other shennanigans. From a flying standpoint, the Stratosurfer as a Twin flies exceptionally well, better I think than with the top mount motor. The power setup I put together for these first flights was certainely powerful enough and amazingly quiet and smooth. With a hard/static mounted Mobius, I saw no jello at any time in the HD recording.

Video

Parting Shot

What a great day!

Project 3D Print Files

All prints were were setup with 50%-80% infill and a 1mm shell thickness. Weights are shown as printed in Hatchbox ABS.

Image	Part Number	Part Description	Weight/Infill	Print File	Compatibility Notes
	52192	Stratosurfer Twin Motor Mount Body	15.3g/60%	52192.STL	22xx size motor mount
	52193	Stratosurfer Twin Motor Mount Front Piece	3.2g/80%	52193.STL	Fits into the mount body, 52192
	52194	Stratosurfer Rear Wing Mount	8.2g/50%	52194.STL	Clamping cover for the rear wing mount
	52156	Stratosurfer Front Wing Mount	14.5g/50%	52156.STL	Low profile wing mount and cover

See Also

• Stratosurfer Build Page
• Parts Catalog - Strix Stratosurfer
• Current Parts Catalogs
• Thingiverse Design Page

Some of the Vendors I used for this project

ReadyMadeRC

GetFPV

Ready to Fly Quads

Comments? Questions?

email me!