Difference between revisions of "GWS S125-1T Servo Mod"
(→See Also) |
|||
| (12 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
| − | <i> | + | <i><small>© Mark Qvale - June, 2016</small></i><br> |
<br> | <br> | ||
{| cellspacing="1" cellpadding="1" width="95%" border="0" | {| cellspacing="1" cellpadding="1" width="95%" border="0" | ||
|- | |- | ||
| − | | align="left" valign=" | + | | align="left" valign="top" width="50%" | __TOC__ |
| align="right" width="50%" | [[File:GWS01.jpg|600px]] | | align="right" width="50%" | [[File:GWS01.jpg|600px]] | ||
|- | |- | ||
| | | | ||
| − | | align="right" width="50%" | Modded! | + | | align="right" width="50%" | !Modded! |
|} | |} | ||
| Line 19: | Line 19: | ||
=== The GWS Servo === | === The GWS Servo === | ||
| − | The <u>current version</u> of the GWS S125-1T Sail Winch servo has decent centering characteristics, will actually travel 385 degrees, it's quite smooth and makes monster torque (~7kg). It is important to note that there are two versions of this servo, one with 23 tooth spline which was discontinued 2 years ago and the one for this project which has a 25 tooth spline identical to Futaba. | + | The <u>current version</u> of the GWS S125-1T Sail Winch servo has decent centering characteristics, will actually travel 385 degrees, it's quite smooth and makes monster torque (~7kg). It is important to note that there are two versions of this servo, one with 23 tooth spline which was discontinued 2 years ago and the one for this project which has a 25 tooth spline identical to Futaba. |
| + | <br> | ||
The easiest way to tell the difference is to look at the servo sticker. | The easiest way to tell the difference is to look at the servo sticker. | ||
<br> | <br> | ||
| − | '''Made in China'''<br> | + | |
| + | '''Made in China Sticker'''<br> | ||
:* This servo has a 23 tooth (JR) spline | :* This servo has a 23 tooth (JR) spline | ||
| Line 30: | Line 32: | ||
<br><br> | <br><br> | ||
| − | '''Made in Taiwan'''<br> | + | '''Made in Taiwan Sticker'''<br> |
:* This servo has a 25 tooth (Futaba) spline | :* This servo has a 25 tooth (Futaba) spline | ||
| Line 37: | Line 39: | ||
<br> | <br> | ||
| − | [[File:GWS_servos.jpg|800px]] | + | {| border="0" cellspacing="1" cellpadding="1" width="95%" align="center" |
| + | |- | ||
| + | | align="center" | [[File:GWS_servos.jpg|800px]] | ||
| + | |- | ||
| + | | align="center" | Two stickers | ||
| + | |} | ||
| + | <br> | ||
=== The Mod === | === The Mod === | ||
| Line 51: | Line 59: | ||
: Center | : Center | ||
| − | [[File:GWS_Boards.jpg|700px]] | + | {| border="0" cellspacing="1" cellpadding="1" width="95%" align="center" |
| + | |- | ||
| + | | align="center" | [[File:GWS_Boards.jpg|700px]] | ||
| + | |- | ||
| + | | align="center" | Two stickers | ||
| + | |} | ||
| + | <br> | ||
| + | |||
| + | Even without the program box the servo works better! No more RF glitches, centering is better than 5 degrees and it runs smoother.<br><br> | ||
| + | |||
| + | == See Also == | ||
| + | <br> | ||
| + | :*[[Heavy Duty Pan and Tilt]] | ||
| + | <br> | ||
| + | |||
| + | === Comments? Questions? === | ||
| + | |||
| + | :'''<u>[mailto:qmar80@hotmail.com?Subject=About%20The%20GWS%20Servo%20Mod&body=Question? email me!]</u>''' | ||
| − | + | <br><br><br> | |
| + | [[Category:Contents]] | ||
Latest revision as of 12:50, 7 July 2019
© Mark Qvale - June, 2016
| |
| !Modded! |
Introduction
So, I wanted a digital version of the GWS S125-1 turn servo to help with RF glitching, centering and to give me the ability to possibly program the end and center points.
The GWS Servo
The current version of the GWS S125-1T Sail Winch servo has decent centering characteristics, will actually travel 385 degrees, it's quite smooth and makes monster torque (~7kg). It is important to note that there are two versions of this servo, one with 23 tooth spline which was discontinued 2 years ago and the one for this project which has a 25 tooth spline identical to Futaba.
The easiest way to tell the difference is to look at the servo sticker.
Made in China Sticker
- This servo has a 23 tooth (JR) spline
- Servo centering will error up to 10 degrees
- This servo was discontinued by GWS in late 2014
Made in Taiwan Sticker
- This servo has a 25 tooth (Futaba) spline
- Servo centering will error up to 5 degrees
- This servo is the current model (as of Oct 2014)
|
| Two stickers |
The Mod
After searching for a very long time for a replacement servo I finally came to the conclusion that the best I could do was to modify the existing servo. I started looking for digital servos that had a small enough board to fit inside the GWS case and it turns out there are many. After trying a few with decent results, I gave a Hitec HS-5245MG board a try and it worked beautifully. It easily fits in the case and it retains all the program functionality.
I found one of these on ebay that was a "parts" servo for $10 so it wasn't too expensive. I already had a Hitec program box from my 3D days so that helped keep it cheap. With the program box, the parameters you can change are-
- Servo Speed
- Deadband
- Endpoints
- Center
|
| Two stickers |
Even without the program box the servo works better! No more RF glitches, centering is better than 5 degrees and it runs smoother.
See Also
Comments? Questions?
